From Audacity Development Manual

Jump to: navigation, search
Gale 19Jul15: ToDo-2 Paul has made numerous observations on this page which should be reviewed in case they improve the accuracy of this page.

Zoomen Zoomer Usando o Zoom Ampliación Zoomen

If you want to carefully inspect a small portion of your audio you will want to use one of these Zoom methods.


The figure above shows Audacity's view of an entire song, zoomed all the way out. It's really useful to get an idea of the whole piece from start to finish, but it's hard to see much detail - like a forest with no individual trees.

Zooming the time scale, or zooming "horizontally", is something you'll do all the time. It lets you focus on the first 15 seconds, for example:


or the last 15 seconds:


or even a tiny fraction of a second, where you can see the individual audio samples as small dots:


Occasionally you may want to zoom "vertically", so that you see only a portion of the waveform from top to bottom, but in greater detail:

If you get lost, refer to the Timeline at the top of the window. It always shows you exactly where you are in time, in hours:minutes:seconds.

Time Scale Zooming (Horizontally)

There are five ways to zoom horizontally:

View Menu

If "Enable scrolling left of zero" is set to be "off" (the non-default setting) then the center of the selection will be positioned at the center of screen.

Use the zoom commands at the top of the View Menu:

  • View > Zoom In: Doubles the current zoom level.
  • View > Zoom Normal: Reverts back to Audacity's default zoom, where you can see 5 - 10 seconds at a time.
  • View > Zoom Out: Cuts the current zoom level in half.
PRL 28May15: Time at screen center is unmoved, unless too near the start of track and "Enable scrolling left of zero" is off
  • View > Zoom to Selection: If you have audio selected, this zooms and scrolls so that the selection just fits in the window.
PRL 28May15: Make a clip, use time shift to drag it partly left of zero, double click the clip, and use this command. Results are anomalous. Width is correct for the selection but horizontal position is not. "Enable scrolling left of zero" does not change that.
  • View > Fit in Window: Zooms out just enough so that you can see the entire project.
PRL 28May15: If some audio is shifted left of zero, it does not display. "Enable scrolling left of zero" does not change that.
  • View > Fit Vertically: This doesn't actually zoom, but resizes all the tracks so they fit in the window vertically without scrolling. If you have more than about ten tracks, some scrolling up and down will still be needed, because there is a minimum track height beyond which reduction is impossible.

Edit Toolbar

Four of the view commands have equivalent buttons on the right of the Edit Toolbar:

  • ZoomIn.png Zoom In
  • ZoomOut.png Zoom Out
  • ZoomSel.png Zoom to Selection
  • ZoomFit.png Fit In Window

Keyboard shortcuts

All six zoom commands have keyboard shortcut equivalents:
PRL 28May15: ditto, sequence
Zoom action Keyboard shortcut
Zoom In CTRL + 1
Zoom Normal CTRL + 2
Zoom Out CTRL + 3
Fit in Window CTRL + F
Fit Vertically CTRL + SHIFT +F
Zoom to Selection CTRL + E

Mac users: Use Command instead of CTRL.

Tools zoom basic7.png Zoom Tool

You can get very precise control over zooming using the Zoom Tool in the Tools Toolbar:


To zoom in, position the mouse pointer over a track and left-click. To zoom out, shift-click or click the right mouse button. The mouse pointer position will remain at the click point, while the length of time visible on the Timeline diminishes or expands on either side to respect the change in zoom level.

PRL 28May15 Again, exceptions to the centering for zooming out when near the start of track, but only when the new Tracks preference is not enabled.

You can zoom in on a specific region by clicking and dragging. Position the mouse at the left edge of the region you require, click and hold the mouse button, then drag the mouse in either direction:


When you release the mouse button, Audacity will zoom in to that region so that it now fits the window:

Shift and drag zooms out based on the dragged region. The smaller the dragged region, the farther the audio will be zoomed out.
PRL 28May15 ditto

If you commence a drag to zoom by mistake, you can press ESC before releasing the mouse to cancel the zoom operation.

Zoom In or Out on the Mouse Pointer using the Scroll Wheel

If your mouse has a scroll wheel or ball, you can zoom in or out centered on the position of the mouse pointer, instead of centered on the selection or editing cursor.
PRL28May15 ditto, centering
Hold down the CONTROL key on your keyboard then scroll up to zoom in, or scroll down to zoom out. For example. you can zoom in at or near the start or end of a selection by placing the pointer there.
Mac users: Hold down both COMMAND and CONTROL while using the scroll wheel.
To zoom the waveform in Audacity without using the CONTROL key, disable "Zoom using scroll ball while holding Command" (or similar) in the System "Mouse" Preferences. If you can't find this option in the Mouse Preferences, look in the System "Universal Access" Preferences, the "Seeing" tab, then in the "Zoom" section click the "Options" button - uncheck "Use scroll wheel with modifier keys to zoom".

Vertical zooming

Vertical zooming can be useful on occasions. You can zoom vertically whichever of the tools in Tools Toolbar are selected. Hover the mouse over the vertical scale of a track, and the pointer changes to a magnifying glass, indicating you can zoom vertically:

  • Left-click once to zoom in at the position on the vertical scale you are interested in. This point will then be centered on the vertical scale.
  • Hold Shift then left-click (or just right-click) to zoom out incrementally.
  • Hold Shift then right-click to zoom out immediately to normal zoom level.
    • Ctrl + Shift with left-click can also be used to zoom out to normal on Mac.

Alternatively, click once and hold down the mouse button, then drag to select a vertical region:


When you release the mouse button, exactly the range you selected will be zoomed in so as to fit vertically inside the track height:


If you commence a drag to zoom in by mistake, you can press ESC before releasing the mouse to cancel the zoom operation.

In default Waveform view set in the Track Dropdown Menu you can zoom in to a minimum display range of 0.001 linear extending from top to bottom of the scale.

Personal tools